Rosemount 848T Specifiche Pagina 36
- Pagina / 136
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
28
Reference Manual
00809-0100-4697, Rev GA
Section 3: Configuration
November 2014
Configuration
55 FD_FAIL_ALM Used primarily to broadcast a change in the associated active conditions, which are
not masked, for this alarm category to a Host System.
56 FD_OFFSPEC_ALM Used primarily to broadcast a change in the associated active conditions, which are
not masked, for this alarm category to a Host System.
57 FD_MAINT_ALM Used primarily to broadcast a change in the associated active conditions, which are
not masked, for this alarm category to a Host System.
58 FD_CHECK_ALM Used primarily to broadcast a change in the associated active conditions, which are
not masked, for this alarm category to a Host System.
59 FD_FAIL_PRI Allows the user to specify the priority of this alarm category.
60 FD_OFFSPEC_PRI Allows the user to specify the priority of this alarm category.
61 FD_MAINT_PRI Allows the user to specify the priority of this alarm category.
62 FD_CHECK_PRI Allows the user to specify the priority of this alarm category.
63 FD_SIMULATE Allows the conditions to be manually supplied when simulation is enabled. When
simulation is disabled both the diagnostic simulate value and the diagnostic value
track the actual conditions. The simulate jumper is required for simulation to be
enabled and while simulation is enabled the recommended action will show that
simulation is active.
64 FD_RECOMMEN_ACT A device enumerated summarization of the most severe condition or conditions
detected. The DD help should describe by enumerated action, what should be
done to alleviate the condition or conditions. 0 is defined as Not Initialized, 1 is
defined as No Action Required, all others defined by manufacturer.
65 FD_EXTENDED_ACTIVE_1 An optional parameter or parameters to allow the user finer detail on conditions
causing an active condition in the FD_*_ACTIVE parameters.
66 FD_EXTENDED_MAP_1 An optional parameter or parameters to allow the user finer control on enabling
conditions contributing to the conditions in FD_*_ACTIVE parameters.
67 COMPATIBILITY_REV Optionally used when replacing field devices. The correct usage of this parameter
presumes the COMPATIBILITY_REV value of the replacing device should be equal or
lower than the DEV_REV value of the replaced device.
68 HARDWARE_REVISION Manufacturer hardware revision
69 SOFTWARE_REV Manufacturer hardware revision
70 PD_TAG PD tag description of device
71 DEV_STRING Used to load new licensing into the device. The value can be written but will always
read back with a value of 0.
72 DEV_OPTIONS Indicates which miscellaneous and diagnostic device licensing options are enabled.
It also indicates Transducer options.
73 OUTPUT_BOARD_SN Output board serial number
74 FINAL_ASSY_NUM Same final assembly number placed on the neck label
75 DOWNLOAD_MODE Gives access to the boot block code for over the wire downloads
76 HEALTH_INDEX Parameter shall be set based on the active FD alarms or PWA alarms.
HEALTH_INDEX will show 100 if target mode of block is OOS or there are no active
alarms in device. The table below represents HEALTH_INDEX value when FD or
PWA alarms are active in a device.
77 FAILED_PRI Designates the alarming priority of the FAILED_ALM and also used as switch b/w FD
and legacy PWA. If value is greater than or equal to 1 then PWA alerts will be active
in device else device will have FD alerts.
78 RECOMMENDED_ACTION Enumerated list of recommended actions displayed with a device alert
79 FAILED_ALM Alarm indicating a failure within a device which makes the device non-operational
80 MAINT _ALM Alarm indicating the device needs maintenance soon. If the condition is ignored,
the device will eventually fail.
81 ADVISE _ALM Alarm indicating advisory alarms. These conditions do not have a direct impact on
the process or device integrity.
Table 3-2. Resource Block Parameters
Number Parameter Description
- Transmitter with FOUNDATION 1
- fieldbus 1
- Transmitter with F 3
- Title Page 4
- 1Section 1: Introduction 5
- 2Section 2: Installation 5
- 3Section 3: Configuration 5
- AAppendix A: Reference Data 6
- DAppendix D: Function Blocks 8
- Section 1 Introduction 9
- 00809-0100-4697, Rev GA 10
- November 2014 10
- OUNDATION fieldbus Technology 10
- 1.3 Service support 11
- Section 1: Introduction 12
- Introduction 12
- Section 2 Installation 13
- 2-in. screws 14
- 2.3 Wiring 16
- RTD or ohm inputs 17
- Analog inputs 17
- 2.4 Grounding 19
- Shielded wire 20
- Grounded thermocouple inputs 21
- Analog device inputs 21
- 2.5 Switches 22
- 2.6 Tagging 22
- Transmitter tag 23
- Sensor tag 23
- 2.7 Installation 24
- 2.7.2 Using conduit entries 25
- Section 2: Installation 26
- Section 3 Configuration 27
- 3.2 Configuration 28
- 3.2.5 Alarms 29
- 3.2.6 Damping 29
- Typical profiling application 31
- OUNDATION fieldbus 33
- Section 3: Configuration 34
- Number Parameter Description 34
- OUNDATION 35
- How to use PlantWeb Alarm 39
- 3.4.3 PlantWeb alerts 40
- MAINT_ALARMS 41
- Advisory alarms 42
- RECOMMENDED_ACTION 43
- FD failed alarms 44
- Configuration 45
- FD CHECK ALARMS 47
- 3.4.7 Transducer blocks 49
- Transducer block errors 50
- Transducer block modes 50
- Automatic (Auto) 51
- Out of Service (OOS) 51
- 4.4.2 Resource block 64
- Appendix A Reference Data 65
- OUNDATION fieldbus parameters 66
- A.3 Function blocks 67
- A.4.1 Stability 68
- A.4.2 Self calibration 68
- A.4.3 Vibration effect 68
- A.4.5 Accuracy 68
- A.4.8 Analog sensors 4–20mA 69
- Reference Data 70
- Examples 71
- A.5 Dimensional drawings 72
- A.5.1 Mounting options 74
- A.6 Ordering information 75
- Approvals 77
- B.3.2 Canada 78
- B.4 Europe 79
- B.5 International 81
- B.5.1 Brazil 83
- B.5.2 China 84
- B.5.3 Japan 86
- B.6 Combinations 87
- B.8 Additional Certifications 88
- B.10 Installation drawings 90
- Product Certificates 91
- Appendix C FOUNDATION 99
- Technology 99
- C.3 Device descriptions 100
- C.4 Block operation 101
- C.5 Network communication 101
- C.5.1 LAS 102
- C.5.2 Addressing 103
- C.5.3 Scheduled transfers 104
- C.5.4 Unscheduled transfers 105
- OUNDATION Fieldbus Technology 106
- Appendix D Function Blocks 107
- Reference Manual 108
- Appendix D: Function Blocks 108
- Table 3-5 on page 11 108
- D.1.1 Functionality 110
- Filtering 111
- Signal conversion 111
- Indirect 111
- Indirect square root 112
- Block errors 112
- Alarm detection 113
- Status handling 114
- Advanced features 114
- Application information 114
- D.2.1 Functionality 118
- D.3.1 Functionality 125
- Block execution 127
- AVG_USE = 6 129
- Numerics 131
Prodotti e manuali riguardandi Misurazione, test & controllo Rosemount 848T
(36 pagine)© 2020, manymanuals.it. Tutti i diritti riservati | 0.027 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale